Clean the windows of the car are not just a matter of hygiene and aesthetics. The driving safety will be compromised if you circulate them very dirty, especially when traveling by day and the sun hits you head on, circumstances where visibility will be reduced drastically if the windshield is dirty. Therefore, in Get Easy Tips are a couple tips on how to clean car windows.
You need
pressure water hose, bucket of soapy water, sponge, rags, newspaper, microfiber cloth, glass cleaner
Instructions
First you have to clean the glass on the outside, with the windows and doors closed completely. It uses a high pressure water hose and fail to remove dirt around the car .
If after cleaning the windows of the car are still out stains, rub them with a cloth dampened with soapy water. Then clear the area with the hose.
For the finishing touch, moistened paper employs water newspaper. Do not be afraid to go to scratch the windows of the car as this will not happen.
Now Car cleanse crystals inside. You must use a bucket of soapy water and a sponge. Apply it all over the surface of the crystals, emphasizing the areas where you have blemishes. Then rinsed with a damp cloth.
To complete the cleaning of the windows of the car inside, use a glass cleaner spray. Spread it with a microfiber cloth. To finish the operation, employs periodic papers moistened in water, just as you did with the outside area.
Clean the glass every time you check that they are dirty. You can not set a time, as they depend on how you use it to drive and the areas where you transites.
The care of the leather seats of the car should be performed with specific products for this item, avoiding moisturizers for people, which ultimately could lead to unwanted effects. In addition to proper cleaning, keep skin in good condition requires him to avoid the sun directly and act immediately before a stain. In Get Easy Tips, we explain how to care for leather seats in the car.
Instructions
Cleanliness is the most important part of caring for leather seats in the car . Keep your skin free of dust is basic, so we recommend that each week passes a vacuum cleaner to remove it.
In addition, once a month you should apply for specific products to clean the skin . At this point, we recommend that you do not reuse moisturizers for people, because in the long run can cause unwanted effects.
Always having spent the vacuum cleaner to remove any dirt, use a microfiber cloth to apply a special cleaning foam skin. 's can be found in supermarkets or shops of auto accessories.
Then apply a lotion to the skin with a sponge. This product will help the leather car seats keeps you hydrated with the passage of time.
It is highly recommended that you always carry in the vehicle a special cleaning wipes for skin if, during a journey, a product falls in the seats and not have time to stop and clean it. The purchase can also in a supermarket.
To prevent the skin from cracking and fading, when you can, avoid the sun hit him squarely on the leather seats in the car . So, leave it parked under cover and in any case, in areas where you can be in the shade.
In the event the skin is already aged, you can use specific products to rejuvenate. Apply the product with a microfiber cloth and leave more than 4 hours at work. It is best to read the manufacturer's instructions for the results to be the best.
The system car air conditioning is complex so the fact that malfunction may be due to many reasons. In some cases, you yourself can locate the fault and repair it, if you have the proper equipment and skill required. However, other faults are difficult to solve and the performance of a professional is needed. In Get Easy Tips we give the answer to the question of why the air conditioning does not cool the car .
Instructions
If your air conditioner does not cool may be because the filter is dirty the interior or jammed. In this case, you yourself can do the cleaning operation or change of this element. Check your car manual to locate it.
Another cause of the air conditioner did not cool is the existence of a refrigerant leak . This may be because, simply, one of the pipe connections are loose. You yourself can locate the leak by putting soapy water in the pipes.
Turn on the air conditioning. Where a leak small bubbles appear. If it is because a connection is loose, simply tighten that. Then you must load the gas air conditioning to replace lost, provided you have the necessary equipment.
If the leak is due to a break , you have to go to a specialized workshop where professionals will be welded and then load the gas.
The compressor of the air conditioner , the key component in the system must be properly lubricated at all times. If, for any damage or poor maintenance, this piece malfunctions, the air is not cold. You must go to a shop for repair.
The air conditioner can not cool due to a power failure that makes the fans do not work well or do so only intermittently. It is best to have a specialist to fix it.
Learn in an easy way and step by step how to change the oil and oil filter in your car.
Instructions
The first thing to do before you get to change the oil in your car is to check that you have everything you need to make the change. An adjustable wrench for oil filter (metal tape), a set of wrenches, screwdrivers two plastic drums which we will take the oil, a funnel and some rags or paper to clean, plus the oil needed for our car and new oil filter that we will add. Once we have all the tools necessary to change the oil in our car, the first thing to do is make sure our car is parked on a plain, never do the oil change with parked on a slope or ramp car. Proceed to remove the covers that protect the underside of the car, whenever I needed to change the oil, because depending on the car model and manufacturer will be no need. We can help a jack to lift the car and remove the housing to more easily. After removing the cover, you will have access to the plug through which we can remove the old oil. The plug must be located at the bottom of the rear of the engine or gearbox. Before unscrewing the cap to extract the oil, we should place right under the plug, drum or container for the oil to go down on him and then store it in another container and taken to a recycling center. Tip: If the engine is hot the oil is much more dilute everything goes perfect, if it is cold out and it costs a lot does not empty well. Be careful if you remove the hot oil as it can be burned. Before removing the oil cap, extract the oil filter wrench helping metal band, although in some cases it is not necessary since we can remove it with your hands. Loosen the oil filter counterclockwise to clockwise, once you've unscrewed very carefully, because the filter will be full of oil, remove and empty the contents into the container. Now proceed to remove the oil cap will fall for this old oil. For better extraction is also recommended to unscrew the top cap of the oil, where we will take the new oil. We must wait a few minutes while the oil goes. Once we have extracted all the oil proceed to put the new oil filter and replace the cap with where we drain the oil. It is recommended to replace the washer that comes with the oil screw, provided that it. Once we have placed the oil filter and closed the outlet of the oil, proceed to fill the engine with new oil, for it can help a funnel to pour the oil no. We will slowly pouring the oil to not spend the oil level. As we go we go throwing checking the oil level with the dipstick. Once you have successfully completed the oil, proceed to place the lower case again. After placement we can re-check the oil level to make sure everything is correct. Since we can only pour oil we have collected in the drum, other airtight container for later taken to a workshop or a clean point, as this type of oil is highly polluting. Do not forget to note the number of miles your car has a role and the tasks performed (change oil and filter) to know when you must change again.
The car air filter affects consumption and engine life, and yourself can check its status or change in a few minutes by following these steps.
Guide to change the air filter car
The air filter is responsible to prevent dirt from entering the engine. Their role is important and does not work properly if dirt can enter the accelerating engine wear and increasing fuel consumption. It is advisable to check the status of air filter every 6,000 km or 6 months (always take whichever comes first), and should be replaced between 12,000 and 18,000 km (8,000 to 12,000 miles) away, depending on the type of car and especially the level of air pollution. Review it is very simple and can do it yourself.
Steps to change the air filter
First you have to locate the air filter in the car engine that is usually contained in a black plastic box or cabinet. In new models usually rectangular and being located on the sides of the engine, near the headlights and wheels and generally rectangular. On older models, the air filter is located on the engine, on the top, and usually round. In both cases you should look for plastic cabinet.
Once we located the container box to remove the air filter is inside. To do this remove the cap almost always secured by hooks or clips to be removed manually, in a few cases the cover is fastened with screws, in which case need a screwdriver to remove them. Already cover removed, we observed that the filter is located and extract it.
The air filter is made up of a paper with many folds. To control the filter cleaning must review the paper for dust, dirt, insects, etc..
If dirt stains covers much of the paper preventing the entry of clean air to the engine's time to change the air filter by an identical, calls for the make and model of the car. If the filter is still able to use it, is convenient to clean injecting pressurized air from a distance that does not damage the paper in the opposite direction in the air through the paper to enter the engine.
Finally took the air filter new or old conditions and we place it in the container box in the same position it was before removing (usually comes only one way), and we cover adjusting screws or placing hooks .
Wash the car at home is a good choice, but to make it spotless and safe from scratching it, keep in mind a few tips.
Tips for washing the car
Auto paint serves to give a good appearance to the vehicle , the better the paint, the better the acceptance of self visually. Being exposed to multiple factors, the painting is one of the parts of the car can suffer more damage. To begin your care, it is important that a good wash will not only remove dirt that may corrode the paint and cause rust, but also protect it, especially applying polishes, Waxing it or polishing. For our car paint always looks shiny and well kept, when washing the vehicle is worth recalling some aspects:
Washing the car
It is best to wash the car often , thus to prevent the deterioration of the paint.
If the car is very dirty or very dirt or dust, not try to clean it with a dry cloth.
To wash it, nothing better than plenty of water and a cloth, sponge or very soft bristle brush. We can leave the water a few moments to soften the dirt before passing the cloth or brush.
First wash the tires and fenders , as they often collect more dirt. Then, starting with the body, from the top down.
If you used some kind of special car shampoo to wash, rinse with clean water and clean using a brush
To dry, opt for another soft cotton cloth or chamois.
If desired, the end and when dry, you can apply a coat of polish. This task should be performed only about 3 or 4 times a year, while polishing should be done 1 time per year.
Both washing and drying, polishing and grinding , are always tasks to be carried out in the shade, as the sun heats the plate accelerating the drying process and may result in loose streaks on the paint.
Note. Do not forget that the parties in which dirt accumulates rust more quickly and easily.
What to do if a battery is discharged and recharged with a charger, or another car.
Causes of discharge of a battery
We have all suffered ever, either in our own car or a car that will be our transport, the dreaded sound off, strangled and died of one battery discharged. Either because they forget to turn off the lights, or radio, or maybe we left a door or trunk open at night: the battery is discharged, and the car will not start. A not despair, that this note will learn to charge the battery simply, even if you've never opened the hood.
How to recharge your car battery
The first sign is the sound off. Turning the key, after contact, the sound of boot donkey is heard making his appearance. And as much as you repeat the task, nothing changes. Well, in this situation the first thing to do is open the hood and check the level of distilled water to the battery . With the car without contact, open the battery and evaluate who has the sufficient amount of liquid, and not have cavity fill. Be sure to close well at the end, and try to start again.
If it has not been a solution, we resort to a battery charger . These devices are extremely simple to use. They have a button or knob that lets you choose between a simple load or starting load. Then connect the clamps to the positive and negative poles of the battery, and plug the device into household outlets. We leave loading (if applicable), or put it up and we start the car.
But if you do not have this device, we need to make bridge with another car battery . You need a wiring harness and special pliers, and a neighbor, friend or relative who has a car to give us your support. We put the car face to face with our own, to make the task easier, and we turned the car savior.
Carefully connect the cables to the battery healthy , respecting the positive and the negative. Once again, very carefully, connect the opposite end of the cables to the battery terminals discharged, first negative and then positive, making sure to respect both the order and classification.
Once done, we drive on to the dead battery, and let it run for a minute or two connected accelerating. We removed the cables carefully, without turning either vehicle speeding car and still recovering for a few more minutes. Then we follow up, we thanked the neighbor, without turning off the car. Remember that the battery will begin charging as you go driving , so you should not stop the march.
In a few minutes we can measure the level of engine compression, and thus have a better idea of the overall condition of the engine over the years.
Attractions for measuring engine compression
The engine compression can be done with ease by a compression tester (gauge), of which can be purchased on the market. This review gives good information on the status of engine wear.
Steps for measuring engine compression
For reviewing reliable compression you need to put the engine at normal operating temperature (85 ° approx. Or recommended by the manufacturer of the car).
With the engine stopped hot and take out all the power lines of the spark plugs. Pay close attention to the order in which the power lines and then connect them in the same position are connected.
Unscrew spark plug and place there the direct reading gauge looking after completely cover the hole in the cylinder head where the plug is inserted.
To measure the engine compression in the cylinder starter (by someone else) is driven for a few seconds with the accelerator pedal fully depressed.
Place the spark plug removed and repeat steps 3 and 4 for each of the remaining cylinder engine.
The pressure read on the gauge should be equal for all cylinders and representative recommended by the engine manufacturer, a difference of 1.5 bar between cylinder gasoline engine allows (when we have the data compression value given by the manufacturer, may use as a general rule the ratio value engine compression adding 1 ie for an engine having a compression ratio of 10:1 will have a pressure value measured on the gauge of 11 (10 +1 )).
A practical way to check the alignment of the car headlights, very important to prevent an accident and properly illuminate all the way.
Steps to align the headlights
If we have the headlights properly aligned with the way we see the full capacity of our headlights and avoid causing accidents with tragic consequences for themselves and others avoid blinding the driver goes in the opposite direction. Before a trip is very important to check and align the headlights that can be affected by adding weight to the vehicle in the rear. It is also advisable to do after changing the front bulbs or lamps. This can be done by a specialist workshop or by oneself without major complications. We know that high or road lights , have a range of about 100 meters depending on the model of the car and power the headlights and illuminate both the opposite lane as their own. Casualties or dipped beam focus closer than our banquina channel without invading the opposite direction to the contrary not dazzle the driver. The high and low beams are differentiated by their internal construction, and highlights as well illuminate a larger area with more light output.
To align the headlights must perform these steps
Locate the vehicle in an area without slopes, flat and well in front of a wall that is perpendicular to the floor (ie no inclination to ground).
From a short distance from the wall (less than 30 cm), turn on the high beams on the wall and mark the point of greatest illumination of each lighthouse. Do the same with the lights low differentiating each brand together.
Zoom the vehicle about 6 feet from the wall in a straight line and turn the lights down low again. The point of greatest illumination is expected to fall by 10% and be in the same line with the earlier mark.
If one does not meet the above condition we proceed to align the car headlight . To do each headlight has two adjustment screws, one moves from top to bottom and the other from right to left. Proceed to move these screws until this point more light straight 5 cm below the first mark.
Now turn on the high road or lights and checked to be between 4 and 5 cm below the high light marks made at the beginning.
If the high and low beam lights are independent, proceed to align the beam with the adjustment screws each to the desired result.
leading cars in the low and high beam in the same headlight if necessary adjust slightly with the same adjustment screws and repeat the previous point to find a point of compromise setting. (The setting of low light or crossing should have higher priority). If it fails to align any of the headlights, we must review the lamps or bulbs are correct and well located within the receptacle. It can also happen that the headlamp control system is broken, in this case you have to go to a specialist for repair or replacement can shop and then if a linear car headlights .
With these instructions on changing the car battery, you can fix the problem it boot and get moving again.
Step by step how to change a car battery
If you have trouble starting your car, mainly in the morning it may be time to check the status of the battery and to change it. To make this process it is necessary that your car's engine is off like all the vehicle components that consume power. As the battery contains a flammable solution is convenient to work in well ventilated areas.
Steps to control and change the battery in your car
Step 1: Ensure that the battery needs replacing First check your appearance, if the battery has cracks or crevices definitely needs to be replaced. Also check the condition of the terminals are the plus and minus buttons that connect to the alternator cables. Sometimes, the sulfate can corrode the terminals or prevent current flow to the motor, remove the guides and clean the contacts can help solve the problem. If your battery is not maintenance free, you should periodically check the level of fluid in it, lack of fluid can cause loss of battery charge . To check the level open covers to see if the solution completely covers the internal plates, if you only see water and no plates then okay,otherwise add distilled water. IF the battery is discharged and you should take to load. In cases of extreme weather can freeze the liquid to get it working again you should take it to a warm place to thaw. Step 2: Remove the battery Once you have determined that you need to change or remove the battery for charging , drain off the Negative Terminal, being careful not to damage it, then Positive, never the other way around because if there is steam battery electrolyte Outdoor This deflagration may occur. Also, check that the battery terminals do not touch, once disconnected, with the metal parts of the vehicle (cover with insulating material) and prevents them from touching each other. Now with a wrench remove the system battery mounting at this point grasp it firmly and remove it from the car. It is important at this time to spend a little time to clean the terminals and tray with a solution of hot water and a little baking soda. If necessary, use a wire brush or sandpaper to clean the terminals well. Step 3: Insert new or recharged battery When buying a new battery, make sure that is the right size and correct orientation. Most vendors can advise you if you tell the make and model of vehicle. Carefully place the new battery into the tray. Recheck that the positive terminal is on the right side. Connect this terminal to the positive terminal, press down and make sure the setting is secure. Repeat with the negative terminal. At this point it would be good to place a thin layer of petroleum jelly around the terminal to prevent rusting. In parts stores can be found in spray products that perform the same function and do not accumulate dirt, but are relatively expensive. Step 4: Close the hood and turn on the car Keep the engine running for a few minutes to take the battery fully charged. Step 5: Discard the old battery The battery old is highly toxic and must dispose of it properly. The best solution is to take it to a recycling center where he recovered a small portion of the investment. This video will help you to change the battery in your car.
Whether you are looking to exit the ride or as a primary means of mobility, here we tell you what to bear in mind when buying a bicycle
Tips for buying a bicycle
Replace motor vehicles by bicycle is a great idea. Healthy, economical, environment friendly, and also available at any time, without major maintenance. The first step in buying a bicycle is to know with certainty what you need. It is the same one for everyday use and townsman, a for weekend trips, even to explore the city, the countryside or mountainous terrain. We recommend our " Types of bicycle to choose "for details on the election. Then, consider also whether it will be for you or if you will share with another person, knowing the most suitable dimensions and weight systems, brakes , change, suspension and other features.
Details to know when buying a bicycle
Scan the table out well . This is the structure, pipe or fiber, and should be chosen based on our body size and weight. Check it fit good, mounting you on bike to correct overall height, seat, pedals distance and size and distance from the handlebars, so to correct your posture while pedaling. These details are part of what is called the size of the bike . Your weight is another point to consider, because there must be an element that can be hoisted and piggybacked to the need, and not resulting in a difficulty pedaling, especially in land elevation. Too lightest bicycle on the other hand, can be somewhat dangerous for children, inexperienced or a walking speed, as possess less stability. You also must take into account the style and brand , as there is a good variety of them, each with different benefits. The styles include a set of features defined for use and maintenance, within which you have the ability to get parts and supplies at good prices in the local market. Note how the handlebars or handlebar of the bicycle , as this will define control you have on road. Please allow an upright posture and walking in urban areas, and a gentle slope with good support in the race. In sports cars, the handlebars must be firm, solid, and very manageable: neither too narrow nor too wide. The system of brakes is very important, because it is safety to drive and react to extreme situations. They may be of rocker horseshoe to disk, and other counter brake. Reiterates its condition and maintenance before buying the bike.
Bicycle Sizes by age
The wheels should fit the size of the user and the bicycle frame, namely: - Cycle 12: they are suitable for children 2-5 years (up to 90 cm in height) - Cycle 14: Up to 103 cm tall - shot 16: For users from 93 to 103 cm tall - Shot 20: From 105 to 120 cm - Cycle 24: Up to 137 cm tall - shot 26 on-wards: Suitable from 137 cm, ie, 10 years of age or older. Adapters (side wheels) will support weights up to 18 kilograms, are very useful for learning and the accompanying shot 12, 14 and 16.
Yes, all have two wheels and pedals, but according to their use can choose different types of bicycles.
Tips for choosing your Bicycle
It seems a simple thing, but choosing a type of Bicycle can take more than a couple of minutes. You must think of it what you want, what your physical endurance, and even how are the streets where you to circulate . Consider the most popular types of shot, and what are its main attributes.
City Bicycle
Are the most common for city use and daily commuting, fairly light, and they can not have or a system of gears and damping, although the basic formats usually choose to minimize costs and increase comfort. You can choose from classic models (more comfortable on the pedal, the position at the walk and wide seat), electric (fall classic, which has been attached in the box a small electric motor that enables walking without pedaling, whether A heavier) and to both folding (folding size shrinks, to keep on reaching the office or in small apartments, are suitable for adults and for a smooth ride and safe areas)
Bicycle for walks
It is a spacious comfortable model, which may or may not have gears or gear shifting, depending on your own requirement. Preferably, takes a big shot and a comfortable, wide seat. If you go to take your friends or your children, make sure that has a rear rack, and even a front basket for carrying items effortlessly. Rides bicycles are lightweight, easy to move, and generally good bandwidth, so before buying you should know if you can upload the stairs, elevator, or give good saves at home.
Mountain Bicycle
This type of Bicycle is much more demanding and technology, and also heavier due to the expected use and the necessary stability. They are chosen for walks and sports in irregular, rocky terrain or scalped. If you'll use in town, you must put tires and narrow smooth or rough and re-branded Single or land. The seat is less wide, like the handlebars, and must have a full set of gear and dampers for a more comfortable driving experience.
Racing bicycles
They are the lightest and narrow, wide box, and redoubled handlebars, allowing the forearm to rest comfortably and according to the body size of the particular user. They have a system of gears and advanced, inconvenient for city riding and commuting compact and lightweight pedal board.
Other Bicycle
There are many other more specific types of bikes in their work, such as BMX, Cross, MTB, the shirts, the Freestyle, hybrid and some more. Your purchase will depend on what the user look at them, and the recommendations of experts in every sport and activity.
A sunny day, ideal for bicycling. You wear a helmet, you dress, you'll look for it and you find that this is faulty or deflated. Avoid these disappointments following some maintenance tips.
How to keep your Bicycle
Already bought your shiny Bicycle ? Well congratulations: you've opted for the healthier means of transport, both for you and for your environment, and is also very easy to maintain. For you to enjoy your Bicycle for a long time, we recommend these simple techniques you can apply daily or as regularly as you prefer him.
Cleaning the Bicycle
For daily hygiene, simply go over the pipes and parts with a soft, dry cloth, preferably cotton. A liquid aerosol product and can help remove stains from spills or other, while the cloth dampened with water will allow you to remove the annoying mud that accumulates in the bottom of the shot. Be sure to clean the chain and parts with grease properly: a soft, dry cloth and remove the dirt clumps, leaving items ready for a review to let you know if you have to add a lubricant. Plastic Bicycle (handles, details, seats, etc.) can be cleaned with a cream product, grease or cleaning multiple surfaces using a soft, clean cloth. After rubbing, go with a barely damp cloth to remove cleaner residue. Finish your dry cleaning something, to remove moisture, grease stains and oils , and even traces of your hands to take it.
Bicycle Grease
As we saw during cleaning you can determine if you have to add grease to the gears, chain and moving parts (like the oil pipe and front steering control). Use suitable grease for bicycles, which can be in paste or liquid. Avoid applying the spray in the chain and wheels, thus leaving more waste than you want. Reserve for use inside the pipes handlebars and seat.
Technical review of the Bicycle
Regularly analyzes the state of the brakes , including cables, hardness and fixing levers, rubber pads contact the rim and others. Make replacements as necessary as soon weakness notes: safe Bicycle brakes should always be in immaculate condition. Daily, or with great regularity, discusses the general condition of the wheels and cameras . You can dip them in water to check with no punctures, inflate when necessary, and check the condition of the valve. Also look closely at the covers or outside of the wheel, analyzing if I had fucking nailed it, at any time, can result in hard way. Finally, check the good condition of the rays, the rotation of the seat and handlebars, and proper fixation and good lubrication of the pedals. Adjust the nuts once a week, although still noticeable, just for being careful, and your Bicycle is always in perfect condition and ready to be enjoyed to the full.
Before you rent a car, pay attention to some of these suggestions, so that you avoid problems and can enjoy the trip without problems.
How to rent a car
We all need at some point in our lives a car. Whether you run a small displacement or to take a well deserved vacation, a car that offers freedom of movement we all need. However, it is not always possible to have one property, either because ours have failed or can not use it at that moment. To troubleshoot the occasional shift, it is best to go to the car rental . Through these services we rented a supplier during a specific time one of the cars in its fleet, which can be used to comply with a number of obligations on our part. These companies usually have corporate websites where we can see the different models that offer even booking the vehicle
Tips for hiring a car
Before renting a car must follow a few tips:
Models . Depending on the characteristics of the trip will need a fairly large car, so we must ensure that the chosen company has sufficient variety of models.
Fleet in good condition . Safety comes first, and so any car is going to hire must have a good condition and have passed all relevant technical inspections.
Provisions of the vehicle . The model you choose should be provided with all the information necessary to deal with any eventuality on the road or, where appropriate, have a help desk.
Policy fuel . We must ensure that we hire the company possesses a fair fuel policy, so only pay for which we consumed.
Extras . There are a number of additional features that can apply to rent a vehicle, such as a question of non-smoking. There are companies have already begun to transform its fleet in a park smoke free vehicles.
If in addition to the above our rental company provides discounts to book in advance, the process of renting a car can become an experience that will have taken a great advantage.
Take care and keep your bicycle in conditions is simple. In addition to that we will last longer, it will also be safer to use.
Tips to keep your bicycle in good condition
With these simple tips you will achieve keep the bike in perfect condition.
Keep the bike clean . Dirt, dust and grease, eventually act as abrasives on the different pieces that make up your shot. Every time you clean, oil the pieces so they do not rust or wear out more.
The wheels must have adequate pressure should be perfectly centered and rays should not be cut or twisted. Change camera after several arrangements.
Always check that the seat and the steering wheel or handlebars are perfectly firm.
Clean lights and cat eyes periodically, if fill dirt or mud, not fulfill the function for which they have been placed on the bike.
Every so controlled that all nuts are snug.
The brakes are very important, must be perfectly tight and smooth braking just use them.
If the chain is too fat oxide and proceeds to clean. When thoroughly dry, lubricate again. One trick is to acid chain sprinkle with the coke and let it get drag grease and rust. It also controls the tension of it, so it does not drop while you're using.
If you're spending a considerable time before returning to bike, it is best to save it hanging on a wall and deflate the wheels a little.
If you like wet, dry it as soon as you can to prevent rust.
Important! Always use a helmet when you use it, but the journey is short. Safety comes first. The helmet should start as a mandatory habit since childhood.
The good smell inside the car also makes the pleasure of handling. Here are some recipes to flavor your car and remove the odor.
Perfumes for Car Home
Confinement, heating, air conditioning, smoking, food and beverage residues, dirt from the environment, all factors that make the car interior accumulate unpleasant aromas. But we have three tips that will help you solve the odor of your car , and an effective solution to keep scented longer.
Remove the bad smell of the car with dry mustard
Mustard has a very strong aroma, it's true. But if you use it diluted in water, it becomes a powerful flavor, able to remove even the strongest odors, such as a piece of food that was left in the car. Mix one cup of dry mustard powder or crushed in a bucket of water beads. Spray and use this liquid to clean the rubber mats, carpets, upholstery, plastics and even the wheels of the car and away the unpleasant smell almost like magic.
Remove the bad smell of the car with fabric softener
When removing clothes washer that we feel sensational smelling clean and fresh. If you want to achieve the same effect in the car, after cleaning and vacuuming carpets and upholstery, put a sheet of fabric softener for clothes at every seat, below the upholstered cover or wherever you prefer. Keep odors at bay, while issue a fresh and delicious fragrance.
Clean the car with white vinegar
This is a degreaser, disinfectant and deodorizer powerful, natural, always at your fingertips. Loads in the car a small tightly closed white spirit vinegar bottle to have on hand. If the vehicle has an unpleasant aroma, aspirated and then reviews the surfaces with a soft cloth soaked in a mixture of equal parts white vinegar and water, or two parts vinegar and water in extreme cases. If you've moved or fertilizer elements ugly smell in the trunk, place a slice of bread soaked in white spirit vinegar and leave it there all night to absorb odors in exemplary fashion.
Flavouring home for car
Cut a shape, small and aesthetics, chipboard school and in a thick cloth or genre, such as upholstery, two units. Adhere the fabric on both sides of the board, and then pour a few drops of your favorite perfume, leaving within an airtight container overnight close the flavor is absorbed and secure to the fabric and cardboard. The next day, put this in your car home flavoring hanging from the rearview mirror or wherever you prefer, and say goodbye to bad smell for a while.
